Sensor Current Dc -15, 5-15, 5A 100V Max Built-In ACS711 0-5V Arduino Compatible

Description

Sensor Current Dc -15, 5-15, 5A 100V Max Built-In ACS711 0-5V Arduino Compatible
The description of this item has been automatically translated. If you have any questions, please feel free to contact us.
Current sensor DC -15.5-15.5A 100V max integrated ACS711 0-5V Arduino compatible
MANUFACTURER: POLOLU
REFERENCE: POLOLU-2452
EAN CODE:
Hall effect DC current sensor -15.5-15.5A max load voltage 100V integrated ACS715 voltage output 0-5V Arduino compatible power supply 3-5.5V DC.
MANUAL DC current sensor with hall effect -15.5-15.5A max load voltage 100V integrated ACS715 voltage output 0-5V Arduino compatible power supply 3-5.5V DC. This current sensor is a carrier board or breakout board for Allegro's ACS711KEXLT-15AB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS711 datasheet (551k pdf) before using this product. This sensor has an operating voltage of 3 V to 5.5 V and an output sensitivity of 90 mV / A when Vcc is 3.3 V (or 136 mV / A when Vcc is 5 V). The following list details some of the sensor's key features: Designed for bidirectional input current from -15.5 A to 15.5 A (though the robust sensor IC can tolerate 100 ms transient current spikes up to 100 A). Conductive path internal resistance is typically 0.6 mΩ, and the PCB is made with 2- oz copper, so very little power is lost in the board. Use of a Hall effect sensor means the IC is able to electrically isolate the current path from the sensor's electronics (for applications up to 100 V), which allows the sensor to be inserted anywhere along the current path and to be used in applications that require electrical isolation. 100 kHz bandwith. Good accuracy and reliability: factory calibration results in a typical total output error of ± 5% at room temperature, the output offset voltage is extremely stable, and the sensor has zero magnetic hysteresis. Overcurrent FAULT output latches low when current magnitude exceeds 15.5 A. Operating temperature range of -40 ° C to 125 ° C. The pads are labeled on the bottom silkscreen, as shown in the picture to the right. The silkscreen also shows the direction that is interpreted as positive current flow via the + i arrow. This 15.5 A current sensor is marked with a black X. We also sell a 31 A version that uses the same carrier PCB; you can distinguish the versions by reading the text on the IC or by looking at the color of the X on the bottom silkscreen. The sensor requires a supply voltage of 3 V to 5.5 V to be connected across the Vcc and GND pads, which are labeled on the bottom silkscreen. The sensor outputs an analog voltage that is linearly proportional to the input current. The quiescent output voltage is Vcc / 2 and changes by 90 mV per amp of input current (when Vcc = 3.3 V), with positive current increasing the output voltage and negative current decreasing the output voltage. The relationship between the instantaneous input current, i, and sensor output voltage, VOUT, can be represented by the following equations: The FAULT pin is normally high and latches low when the current exceeds ± 15.5 A. Once the FAULT pin is latched low, the only way to reset it is by toggling power on the Vcc pin. In our tests, this module was able to handle 15 A of continuous current without exceeding 50 ° C, with no cooling beyond the heat dissipation of the PCB. Manufacturer POLOLU Type of current sensor Supply voltage 3 ... 5.5V DC Integrated circuit ACS711 Current measurement range DC -15.5 ... 15.5A Sensitivity of current detection 0.09V / A Dimensions of the plate 17.8 x 20.3mm Information The product is not a complete device, it is only a component Additional information Gross weight: 2.65 g
Why
Mec
tronic
STORE
? Few and simple principles.
All products are shipped via the best national couriers such as SDA, GLS, Poste Italiane, BRT and DHL. To facilitate delivery, you will be asked for your telephone number when ordering, allowing the courier to contact you in case of any problem or eventuality in the delivery. For any delivery needs you can contact us.
ALL SHIPMENTS ARE 100 TRACEABLE
Not home during the day? We have the possibility to deliver to the post office near your home or to a Puntoposte! Write the delivery point in the address.
PAYMENT
Credit cards are also accepted with transactions always made on the secure payment site PayPal. No information about your payment method is shared with us to ensure maximum security.
A REGULAR TAX INVOICE IS ISSUED FOR THE PRODUCTS SOLD IF REQUIRED AT THE TIME OF PURCHASE.
WITHDRAWAL AND WARRANTY
All our products are guaranteed both on delivery and in the time of use. For original defective products we carry out the free replacement of the product. The warranty has a duration of 2 years for individuals and 1 year for companies / businesses. Remember to keep the sales invoice and the original packaging of the product with all accessories aside! If you are not satisfied with a product, you have 30 days to withdraw from the purchase and receive a refund for the purchase of the product.
TECHNICAL ASSISTANCE
What differentiates us from other sellers? We are an electronics company with technicians dedicated to solving your doubts or problems with our products. No waiting on the phone or call center: you can contact us by phone, whatsapp, email or fax, the references can be found at the bottom of the page. Our experience is at your service to help you in the choice and use of the products on sale.
FEEDBACK
Feedback is important to us and to you. Therefore we ask you to report any problems in the sale and to contact us before the release of negative or neutral feedbak. Remember to put 5 stars in your feedback if possible on all fields to always guarantee the service we offer. As you can see, the way to contact us is clear and simple, to quickly resolve all problems with our products.
ELECTRONICS - HOME AUTOMATION - REMOTE CONTROLS - AUTOMATION AND MECHANICS - SOFTWARE REALIZATIONS
Prestalia
e-commerce solutions.
MANUAL DC current sensor with hall effect -15.5-15.5A max load voltage 100V integrated ACS715 voltage output 0-5V Arduino compatible power supply 3-5.5V DC. This current sensor is a carrier board or breakout board for Allegro's ACS711KEXLT-15AB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS711 datasheet (551k pdf) before using this product. This sensor has an operating voltage of 3 V to 5.5 V and an output sensitivity of 90 mV / A when Vcc is 3.3 V (or 136 mV / A when Vcc is 5 V). The following list details some of the sensor's key features: Designed for bidirectional input current from -15.5 A to 15.5 A (though the robust sensor IC can tolerate 100 ms transient current spikes up to 100 A). Conductive path internal
MPN
POLOLU-2452
EAN
Non applicabile
Marca
POLOLU
UPC
Non applicabile